Skip to content

hBARSCI is now The Lab Stockroom

Glassware Knowledge Center

Glassware Calibration Certificates: Batch vs. Individual vs. Accredited

Volumetric glassware is certified at three levels: batch, where a tested sample stands for the whole production lot; individual, where each piece is calibrated and gets its own serial-numbered certificate; and accredited, an individual calibration by an ISO/IEC 17025 accredited laboratory. Accredited certificates carry the most readings per piece and the lowest stated uncertainty.

Calibration Certificate Key Facts

Batch certificate Reports the mean volume and standard deviation for a production lot, based on a tested sample
Individual certificate Reports one piece's measured volume and calibration uncertainty, matched by its serial number
Accredited certificate An individual calibration issued by a laboratory accredited to ISO/IEC 17025
Certificate of Conformity Declares that a batch meets its stated material and specification; it does not report measured volumes
Which glassware Individual and accredited certificates are issued for Class A glassware
Calibration method Gravimetric, under ISO 4787: water is weighed and converted to volume; see How Volumetric Glassware Is Calibrated
Rule of thumb Routine teaching labs rarely need accredited certificates; regulated labs often do

What Are the Levels of Glassware Calibration Certificates?

Calibration certificates for volumetric glassware come in three levels. Each one tells you more about the exact piece in your hand, and each takes more work to produce.

New to the terms? Start with What Is Volumetric Glassware?

Batch Individual Accredited
What is measured A sample from the production lot Each piece, on its own Each piece, with more readings
What the certificate reports Lot mean volume and standard deviation That piece's volume and uncertainty That piece's volume and uncertainty, plus lab conditions, equipment and procedure
Where it is done Manufacturer's calibration lab Manufacturer's calibration lab A laboratory accredited to ISO/IEC 17025
Uncertainty Estimated for the lot Stated for the piece Lowest stated
Typical use Routine work where lot-level records are enough QC and documented work that needs a record per piece Regulated labs and audits that call for accredited calibration
  1. Accredited (ISO/IEC 17025)Individual calibration in an audited laboratory, most readings, lowest stated uncertainty
  2. IndividualEach piece calibrated, with its own certificate by serial number
  3. BatchA tested sample stands for the lot

Calibration certificate levels, from highest (top) to lowest (bottom).

What Does Each Certificate Report?

A batch certificate covers a production lot. A sample from the lot is calibrated, and the certificate gives the lot's mean volume and standard deviation. It tells you the lot is in tolerance, not the exact volume of your piece.

An individual certificate covers one piece. That piece is calibrated on its own, and the certificate gives its measured volume and the uncertainty of the calibration. A serial number on the glass matches the piece to its certificate. Individual certificates are issued for Class A glassware; see Class A vs. Class B Glassware.

An accredited certificate is an individual calibration done by a laboratory that an accreditation body has audited against ISO/IEC 17025. It also records the laboratory's conditions, the equipment and the procedure used.

Why Do Accredited Certificates Cost More?

Each step up the hierarchy adds work per piece. An individual certificate means calibrating every piece instead of a sample. An accredited certificate adds more readings per piece, done in an audited laboratory on auditor-approved equipment, and carries the lowest stated uncertainty. That added work is why accredited certificates cost more than individual and batch certificates.

Certificate of Conformity vs. Calibration Certificate

A Certificate of Conformity, also called a Certificate of Compliance, declares that a batch meets its stated material and specification, such as the glass type, class and standard. It is a statement, not a measurement. A calibration certificate reports measured results: the volume found and, for individual and accredited certificates, the uncertainty. Labs that need proof of a measured volume need a calibration certificate.

Which Calibration Certificate Does Your Lab Need?

Match the certificate to how the result will be used. Routine teaching labs rarely need accredited certificates, and many use Class B glassware with no certificate at all. QC and documented work usually call for Class A with an individual certificate, so each piece has its own record. Regulated labs often require accredited calibration, so check what your method, SOP or auditor specifies.

Do You Need NIST Traceable Glassware?

NIST is the US national metrology institute: it maintains the national measurement standards. India's counterpart is CSIR-NPL. Accreditation bodies do a different job. A2LA and ANAB in the US, and NABL in India, audit calibration laboratories against ISO/IEC 17025. US accreditation bodies accept results traceable to the International System of Units (SI) through NIST or another national metrology institute (see, for example, Perry Johnson Laboratory Accreditation's traceability policy), so an accredited laboratory does not need to trace to NIST specifically.

Under its policy on metrological traceability, NIST certifies the traceability only of measurements it makes itself, and its traceability FAQ treats "traceable to NIST" as shorthand for traceability through NIST to the SI. Accreditation bodies that sign the Global ACI mutual recognition arrangement (formerly the ILAC MRA), including NABL, treat calibration results from each other's accredited laboratories as equivalent; see Laboratory Glassware Standards Explained. Every calibration certificate should state its traceability source; your method, SOP or auditor decides which sources are acceptable.

Calibration Certificate FAQs

What is the difference between a batch certificate and an individual certificate?

A batch certificate reports the mean volume and standard deviation for a production lot, based on a tested sample. An individual certificate reports the measured volume and uncertainty of one specific piece, matched by its serial number. The Lab Stockroom carries Class A glassware with batch or individual certificates.

What is a Certificate of Conformity?

It is a document declaring that a batch meets its stated material and specification, such as the class and standard. It does not report measured volumes; a calibration certificate does. The Lab Stockroom carries Eisco Class A volumetric glassware, which is supported by a Certificate of Compliance for its batch.

What is ISO 17025 accredited calibration?

ISO/IEC 17025 is the international standard for the competence of testing and calibration laboratories. An accredited calibration is done by a laboratory an accreditation body has audited against it, so the certificate's results and uncertainty carry that recognition. Eisco, one of the manufacturers The Lab Stockroom carries, offers accredited certificates on select Class A volumetric glassware.

Which certificate does a teaching lab need?

Usually none beyond what comes with the glassware. Routine teaching work rarely needs accredited certificates, and Class B glassware is calibrated without an individual certificate. The Lab Stockroom stocks Class B for everyday teaching and Class A with certificates for documented work.

Standards Referenced

  • ISO/IEC 17025: competence of testing and calibration laboratories
  • ISO 4787: calibration method for volumetric glassware
Manufacturer Spotlight

Eisco Calibration Certificates

Eisco issues three calibration certificates for volumetric glassware: Batch Test, Eisco Work (individual) and NABL, an accredited calibration under ISO/IEC 17025 from India's National Accreditation Board for Testing and Calibration Laboratories. Batch Test and Eisco Work calibrations can be done at any Eisco site; NABL calibrations are done only in Eisco's audited laboratory, on auditor-approved equipment.

1 Reading or 10Eisco Work takes one reading per piece; NABL takes ten.
ISO 4787 MethodEisco calibrates gravimetrically, weighing water and converting it to volume.
QR to CertificateEisco volumetric flasks and measuring cylinders carry a QR code that links to the batch certificate.